Setup Guide for Teslacigs Stealth 40w with Saionara or Divine  Crossing v3 Atomizer

Please read this manual carefully before using your Mod or Atomizer to ensure proper use.

Step One

Gather your Stealth 40w and Atomizer.

The Teslacigs Stealth 40w is a 40w maximum output device powered by an internal 1300 mAh 20A LiPo Battery and supports the following modes: Variable Wattage, Bypass, TC-Ni, TC-Ti, and TC-SS.

Depending on your Atomizer and Coil, you will be using the Variable Wattage, TC-Ni, or TC-SS modes only.

Please make sure you sufficiently charge your device before following this guide.

Step Two

Due to the small size of the device and limited screen size, the Tesla Stealth 40w is not as user friendly as some other mods.

You can Lock and Unlock the device by pressing the Fire button 5 times in succession. Make sure the device is Locked for the next steps.

Before connecting the Atomizer, we are going to set the Stealth 40w into a safe range to ensure we do not damage any of our coils.

Lets start by putting our Stealth into Wattage Mode. Make sure the device is locked and simultaneously press the Up and Down buttons, the screen should display "Hold to Change Temp".

Press the Up button to adjust the temperature past 600 Fahrenheit, the screen will display "Off". You are now in Wattage Mode.

Now use the Down button to set the wattage to around 10.0w, then press the Fire button. This should be a safe setting for any of the coils we will be using in the guide.

Step Three

Screw the Saionara or Divine Crossing v3 Atomizer into the recessed 510 threaded connector on the Teslacigs Stealth 40w. Make sure you have a coil installed.

The Atomizer and Coil that you are using will determine which Vaping Mode and Power Level you need to be using to ensure the best vaping experience.

If you followed Step Two, you should currently be in Wattage Mode and set to 10.0w. Screw on the Atomizer and press the Fire button, the Stealth will prompt you to select your Coil Type. Use the Up or Down buttons to select the "Normal" option and press the Fire button.

We are using a Saionara Atomizer with a brand new Miracle A Coil that reads at 0.56 ohms. If you see No Atomizer on the screen, make sure everything is screwed down tight.

Each coil resistance can vary slightly, so do not worry if yours is not exactly the same.

Step Four

Now we need to put your Stealth into the correct Vaping Mode for the coil you are using.

Saionara Wax Coil, Miracle Coils:

If you are using the Saionara Atomizer with the  Original Wax Coil, Miracle Coil A, or Miracle Coil B you do not need to change modes as these coils run in Wattage Mode Only. Proceed to the next step.

Saionara Black Ceramic / Stainless Steel:

If you are using the Saionara Atomizer with the Black Ceramic / Stainless Steel coil, you will need to put the Stealth into Stainless Steel Temperature Control Mode.

Unscrew the Atomizer from the Stealth, screw it back down, then press the Fire button. The screen should display "Temp Coil Select".

Press the Up or Down button to select "SS" mode, then press the Fire button. If you are asked Same / New coil, choose New.

Divine Crossing v3:

If you are using the Divine Crossing v3 Atomizer, you will need to put the Stealth into Nickel Temperature Control Mode.

Unscrew the Atomizer from the Stealth, screw it back down, then press the Fire button. The screen should display "Temp Coil Select".

Press the Up or Down button to select "Ni" mode, then press the Fire button. If you are asked Same / New coil, choose New.

Coil Settings

Now that you are in the correct Vaping Mode, find the correct settings below for the coil you are using. Note that these settings are recommendations only so feel free to experiment with what works best for you. If you are unsure, start low and work your way up.

Original Wax Coil: 15-28 Watts.

Miracle A: 7-15 Watts.

Miracle B: 7-15 Watts.

Black Ceramic / Stainless Steel: 15 Watts @ 320-440 Fahrenheit. (SS mode)

DC v3 10mm Donut: 30 Watts @ 300 - 340 Fahrenheit. (Ni mode)

DC v3 13mm Donut: 25 Watts @ 350-420 Fahrenheit. (Ni mode)

Adjust Temperature:

Press the Fire button 5 times in quick succession to lock the device.

Make sure the device is locked and simultaneously press the Up and Down buttons, the screen should display "Hold to Change Temp".

Press the Down or Up button to adjust the temperature to your desired setting, then press the  Fire button. 

Resistance Lock:

Temperature Control works best when you lock the resistance of your coil. This should be done when you first install your new coil and when the device is at room temperature. Locking your resistance lets your device know the correct baseline so that temperature calculations work more accurately.

To Lock / Unlock resistance, press and hold the Fire button and Up button simultaneously for two seconds. The Lock or Ohm sign will appear depending on the current setting.

Always make sure to Lock/Unlock resistance when changing to a new coil.

Adjust Wattage:

Once the temperature is set, press the Fire button 5 times in quick succession to unlock the device.You can now use the Up or Down buttons to adjust the Wattage to the appropriate setting.

Power Lock:

Power Lock is optional but is recommended if you will be carrying the device in a pocket. This will ensure that your settings do not get changed accidentally.

Press and hold the Fire button and Down button simultaneously for two seconds. The screen will display Power Lock and you will no longer be able to adjust the Wattage.

Loading and Using

Place a rice-grain or larger sized piece of concentrate directly into the atomizer, the best place to load will depend on the type of coil you are using.

Pulse the Fire button lightly to melt the concentrate onto your coil and replace your atomizer cap.

For Wattage Mode Coils: 

You will need to pulse your Fire button to ensure you do not overheat your concentrate while vaping.

Most users report a 5-4-4 pattern works well, this means holding the button for approximately 5 seconds, letting go of the button for a half second, fire for 4 seconds, etc.

For Temperature Mode Coils:

No instructions are necessary for Temperature Control coils. Simply hold the  Fire button down and inhale, your Stealth will internally pulse your Atomizer to maintain proper temperatures.

Note: there is still a 10 second automatic cutoff in TC mode

 Your device is now setup and ready to use.

If you have a question related to the Teslacigs Stealth 40w that is not covered in this manual, you can access the full manual from the manufacturer website. Any other questions can be emailed directly to MaxVapor:

support@maxvapornail.com